Tipo de rolamento |
Dimensão de forma externa Dimension(mm) |
Carga load nominal |
Limiting Speed r/min |
Qualidade |
|||||||||
New Code |
Old Code |
d |
d1min |
D |
D1max |
H |
α |
rsmin |
Ca(KN) |
Coa(KN) |
Grease |
Oil |
(Kg) |
569184 | 9168184 | 420 | 430 | 500 | 490 | 48 | 60° | 2 | 260 | 1440 | 830 | 1100 | 15.9 |
567284 | 7168284 | 420 | 462 | 580 | 538 | 73 | 45° | 5 | 330 | 2010 | 700 | 980 | 51 |
569188 | 9168188 | 440 | 458 | 540 | 522 | 60 | 45° | 2.1 | 380 | 1980 | 650 | 950 | 25.5 |
5691/500 | 91681/500 | 500 | 530 | 600 | 570 | 60 | 60° | 2.1 | 322 | 1956 | 660 | 950 | 25.3 |
5613/520 | 1689/520 | 520 | 554 | 620 | 586 | 60 | 60° | 2.1 | 409 | 2247 | 400 | 570 | 26.9 |
5692/530 | 91682/530 | 530 | 590 | 710 | 650 | 109 | 60° | 5 | 738 | 4162 | 350 | 500 | 90.3 |
5617/560 | 1687/560 | 560 | 620 | 740 | 680 | 89 | 45° | 6 | 805 | 3432 | 400 | 570 | 77 |
5991/600 | 91681/600 | 600 | 635 | 675 | 710 | 67 | 60° | 3 | 504 | 3010 | 510 | 710 | 37.6 |
5617/610 | 1687/610 | 610 | 700 | 790 | 735 | 89 | 45° | 4.5 | 840 | 3648 | 380 | 540 | 86 |
5617/620 | 1687/620 | 620 | 665 | 780 | 735 | 102 | 45° | 3.5 | 776 | 3588 | 340 | 490 | 95.1 |
5692/620 | 91682/620 | 620 | 680 | 800 | 740 | 109 | 60° | 5 | 902 | 4720 | 260 | 370 | 103.1 |
5617/650 | 1687/650 | 650 | 690 | 880 | 840 | 140 | 60° | 6 | 1100 | 7280 | 260 | 370 | 200 |
5692/670 | 91682/670 | 670 | 740 | 900 | 830 | 140 | 45° | 6 | 1260 | 6085 | 250 | 360 | 206 |
5691/750 | 91681/750 | 750 | 780 | 900 | 870 | 90 | 60° | 4 | 587 | 4620 | 340 | 480 | 94.4 |
5611/800 | 1681/800 | 800 | 850 | 950 | 900 | 120 | 60° | 4 | 866 | 6414 | 200 | 240 | 133.6 |
5692/800 | 91682/800 | 800 | 890 | 1060 | 970 | 155 | 60° | 7.5 | 1134 | 9394 | 180 | 180 | 301.9 |
5617/810 | 1687/810 | 810 | 880 | 1030 | 960 | 110 | 45° | 7.5 | 780 | 4080 | 280 | 400 | 176 |
5691/950 | 91682 | 950 | 1040 | 1250 | 1160 | 180 | 45° | 7.5 | 1500 | 9168 | 120 | 170 | 432 |
5691/1000 | 91681/1000 | 1000 | 1040 | 1180 | 1140 | 109 | 45° | 5 | 1076 | 6516 | 250 | 360 | 177 |
5691/1120 | 91681/1120 | 1120 | 1170 | 1320 | 1270 | 122 | 60° | 5 | 1020 | 10270 | 180 | 260 | 241 |
5617/1600 | 1687/1600 | 1600 | 1600 | 1760 | 1760 | 90 | 60° | 6 | 685 | 8055 | 210 | 300 | 248 |
5617/1860 | 1687/1860 | 1860 | 1900 | 2100 | 2060 | 140 | 60° | 4.5 | 1275 | 19370 | 92 | 130 | 577 |
LYNB thrust ball bearings are separable, i.e. the shaft washer, housing washer(s), ball and cage assembly(s) can be mounted separately. Shaft washers have a ground bore to enable an interference fit. The bore of the housing washer is turned and always larger than the shaft washer bore. LYNB thrust ball bearings are produced as single direction or double direction thrust ball bearings and angular contact thrust ball bearing. They are designed to accommodate axial loads only and must Tipo sem engrenagemt be subjected to any radial load.
The angular contact thrust ball bearing mainly carries axial load, and it can also carry a certain radial load. Compared with thrust ball bearings of the same dimension, the limiting speed is also higher. It can make an axial location in one direction. Angular contact thrust ball bearings can make up for the weakness of the thrust ball bearings with flat back face which canTipo sem engrenagemt carry radial loads. The contact angles are 45°and 60°.The smaller the degree of contact angle, the higher the capacity of the radial load is.
LYNB can provide thrust ball bearings with other special structures, such as thrust ball bearings without cages, unidirectional thrust ball bearings with taper bores, unidirectional thrust ball bearings with steel wire raceway and etc. All the types canTipo sem engrenagemt be listed in this catalogue.
▲ LYNB can design and manufacture many other similar structures in accordance to the special and particular requirements of their customers’. If our customer’s have specific requests then the customer should identify the structure, and Dimensão de furos de montagem dimensions that are required. Please contact the LYNB Technical Center if you need any assistance in this area.